Lc2i 4 channel amp. The LC2i is a two-channel processor that accepts signals up to 499 watts fo...
Lc2i 4 channel amp. The LC2i is a two-channel processor that accepts signals up to 499 watts for each channel from existing factory installed systems or amplifiers. Thanks for any advice given. This powerful unit converts speaker-level signals—up to 400W per channel—into high-quality pre-amp outputs, making it ideal for aftermarket components. Make sure the signal going to the input of the LC2i is a full range signal otherwise it will not sound right. The LC2i, is a compact, two-channel processor with active input circuitry, which allows it to accept speaker-level signals of up to 400 watts per channel from factory-installed source units or amplifiers. 5” DS18 Dec 5, 2025 路 The AudioControl LC2i is a 2-channel active line output converter designed to integrate aftermarket amplifiers with factory audio systems. Jun 8, 2015 路 If you're going to run a mono amp and a 4 channel amp, you'd need an LC6i or an LC7i in order to sum the signals into a pseudo full range signal. Can the LC2i be used inline with a 4 channel amp to power my front components speakers and a subwoofer? I feel like I’m overthinking this, but I’m just trying to clear this up. Please Full audio install from Quality Care Detailing 馃攰 Contact us for quotes on audio 馃 This was a crazy modification to this 2021 Jeep Wrangler Unlimited Sport Factory Mids swapped for DS18 Factory Tweeters swapped for DS18 Added 10” CTSounds subwoofer All ran on 6 channel CT Sounds Amp Equipment Used 鈴笍 • CTSounds 6 Channel 1,500 Watt • LC2i Line Converter • 4 - 3. Built a two layer rack and that fits behind the rear seats and the gap of the trunk opening. I have installed a lc2i Pro loc and a 5 channel amp (no sub yet) in my 2019 Subaru Outback, when I turn on the ignition (subaru turns infotainment sys on Managed to install my aftermarket amps and sub. The LC2i then sends out a high-powered preamp signal — up to 9. 99 Free delivery Sponsored Line Output Converter 2 Channel LC2i AudioControl AccuBASS Subwoofers Amplifiers $92. Convenience The optional dash-mount remote control allows you to adjust the level of your sub channel on the go. 99 Free delivery Sponsored. 5 days ago 路 $128. Find the complete wiring diagram for installing an Audiocontrol lc2i in your car and enjoy high-quality audio performance. One being a full range audio signal, the other being a switched power source. This item is listed as New and categorized under Signal Processors. The line out converter I chose to use (AudioControl LC2i) requires a power source and a turn on just like an amplifier. Used Audio Control LC2i 2 channel active line output converter Designed to work with most factory systems inputs and outputs 400 watts RMS power handling per channel @ 4 ohms AccuBASS circuitry Recommended fuse rating: 1amp Note: Aftermarket accessory and though DIY is possible, professional installation is recommended. The 4 channel amp is just there but not hooked up to anything since I'm still on the fence about replacing front speakers but didn't want to have to redo the rack later. Feb 20, 2026 路 I have a LC2i 2 channel converter and a Wavetech link 4 channel converter. 5 volts RMS — that helps every amp perform to its maximum ability. The LC2i converts signals from those old units into higher-quality signals and sends them on to your factory installed or aftermarket processors. No instruction except the manufacturer original if there is any. Ensure that the aftermarket amp has a 2 channel option for its 4 speaker outputs. This turn on can be accomplished two different ways. Can a lc2i pro be used for sub amp and 4 channel at the same time The conversation revolves around using a factory head unit with aftermarket amps and Nov 17, 2010 路 饾棬饾椊饾棿饾椏饾棶饾棻饾棽 饾槅饾椉饾槀饾椏 饾棶饾槀饾棻饾椂饾椉 饾榾饾槅饾榾饾榿饾棽饾椇 饾槃饾椀饾椂饾椆饾棽 饾椄饾棽饾棽饾椊饾椂饾椈饾棿 饾槅饾椉饾槀饾椏 饾棾饾棶饾棸饾榿饾椉饾椏饾槅 饾榾饾榿饾棽饾椏饾棽饾椉: Convert speaker-level signals up to 400W per channel from your OEM radio or amplifier to high quality pre-amp output signals directed to aftermarket subwoofers, amplifiers, and processors. 2 days ago 路 Check Price On Amazon! Integrating a subwoofer into your factory car audio system has never been easier, thanks to the AudioControl LC2i PRO 2-Channel Active Line Output Converter. I used the LC2i to process the signal from the factory system to an Alpine amp and a pair of 10’ Alpine type R subs. I’ll be running a 4 channel amp for high’s and a mono amp for subs. It includes AccuBASS to help manage bass response when working with OEM signals. 00 Free delivery AudioControl LC2i Line Out Converter 2-Channel with AccuBASS Sub Control The AudioControl LC2i 2-channel line out converter is designed for integrating aftermarket amplifiers or subwoofers with factory audio systems. The LC2i will only work for adding a sub amp. Step-by-step instructions and visuals included for easy installation. Aug 28, 2024 路 Not required but a very good choice. People who viewed this item also viewed AudioControl LC2i PRO 2-Channel Active Line Output Converter/Line Driver/ACR-1 $128.
